For the processing of aluminium Further technical information: · d: 6.35mm · Area of application: Aluminium processing · r: 0.4mm · d1: 2.8mm · s: 3,18mm · l: 11,1mm · Max. feed rate: - mm/rev in steel / - mm/rev in stainless steel / - mm/rev in cast / 0.2 mm/rev in NI metals / - mm/rev in superalloys / - mm/rev in hardened steels · Vc max.: - m/min in steel / - m/min in stainless / - m/min in cast / 505 m/min in NI metals / - m/min in superalloys / - m/min in hardened steels · Vc min.: - m/min in steel / - m/min in stainless / - m/min in cast / 135 m/min in NI metals / - m/min in superalloys / - m/min in hardened steels · Min. cutting depth: - mm in steel / - mm in stainless / - mm in cast / 0.4 mm in NI metals / - mm in superalloys / - mm in hardened steels · Max. cutting depth: - mm in steel / - mm in stainless / - mm in cast / 2.8 mm in NI metals / - mm in superalloys / - mm in hardened steels · Min. feed rate: - mm/rev in steel / - mm/rev in stainless steel / - mm/rev in cast / 0.1 mm/rev in NI metals / - mm/rev in superalloys / - mm/rev in hardened steels

For the processing of aluminium Further technical information: · d: 6.35mm · Area of application: Aluminium processing · r: 0.4mm · d1: 2.8mm · s: 3,18mm · l: 11,1mm · Max. feed rate: - mm/rev in steel / - mm/rev in stainless steel / - mm/rev in cast / 0.2 mm/rev in NI metals / - mm/rev in superalloys / - mm/rev in hardened steels · Vc max.: - m/min in steel / - m/min in stainless / - m/min in cast / 420 m/min in NI metals / - m/min in superalloys / - m/min in hardened steels · Vc min.: - m/min in steel / - m/min in stainless / - m/min in cast / 110 m/min in NI metals / - m/min in superalloys / - m/min in hardened steels · Min. cutting depth: - mm in steel / - mm in stainless / - mm in cast / 0.4 mm in NI metals / - mm in superalloys / - mm in hardened steels · Max. cutting depth: - mm in steel / - mm in stainless / - mm in cast / 2.8 mm in NI metals / - mm in superalloys / - mm in hardened steels · Min. feed rate: - mm/rev in steel / - mm/rev in stainless steel / - mm/rev in cast / 0.1 mm/rev in NI metals / - mm/rev in superalloys / - mm/rev in hardened steels

For the processing of aluminium Further technical information: · d: 9.525mm · Area of application: Aluminium processing · r: 0.4mm · d1: 4.4mm · s: 4,76mm · l: 16,6mm · Max. feed rate: - mm/rev in steel / - mm/rev in stainless steel / - mm/rev in cast / 0.2 mm/rev in NI metals / - mm/rev in superalloys / - mm/rev in hardened steels · Vc max.: - m/min in steel / - m/min in stainless / - m/min in cast / 505 m/min in NI metals / - m/min in superalloys / - m/min in hardened steels · Vc min.: - m/min in steel / - m/min in stainless / - m/min in cast / 135 m/min in NI metals / - m/min in superalloys / - m/min in hardened steels · Min. cutting depth: - mm in steel / - mm in stainless / - mm in cast / 0.4 mm in NI metals / - mm in superalloys / - mm in hardened steels · Max. cutting depth: - mm in steel / - mm in stainless / - mm in cast / 4 mm in NI metals / - mm in superalloys / - mm in hardened steels · Min. feed rate: - mm/rev in steel / - mm/rev in stainless steel / - mm/rev in cast / 0.1 mm/rev in NI metals / - mm/rev in superalloys / - mm/rev in hardened steels

For the processing of aluminium Further technical information: · d: 9.525mm · Area of application: Aluminium processing · r: 0.4mm · d1: 4.4mm · s: 4,76mm · l: 16,6mm · Max. feed rate: - mm/rev in steel / - mm/rev in stainless steel / - mm/rev in cast / 0.2 mm/rev in NI metals / - mm/rev in superalloys / - mm/rev in hardened steels · Vc max.: - m/min in steel / - m/min in stainless / - m/min in cast / 420 m/min in NI metals / - m/min in superalloys / - m/min in hardened steels · Vc min.: - m/min in steel / - m/min in stainless / - m/min in cast / 105 m/min in NI metals / - m/min in superalloys / - m/min in hardened steels · Min. cutting depth: - mm in steel / - mm in stainless / - mm in cast / 0.4 mm in NI metals / - mm in superalloys / - mm in hardened steels · Max. cutting depth: - mm in steel / - mm in stainless / - mm in cast / 4 mm in NI metals / - mm in superalloys / - mm in hardened steels · Min. feed rate: - mm/rev in steel / - mm/rev in stainless steel / - mm/rev in cast / 0.1 mm/rev in NI metals / - mm/rev in superalloys / - mm/rev in hardened steels

For the processing of aluminium Further technical information: · d: 9.525mm · Area of application: Aluminium processing · r: 0.2mm · d1: 4.4mm · s: 4,76mm · l: 16,6mm · Max. feed rate: - mm/rev in steel / - mm/rev in stainless steel / - mm/rev in cast / 0.1 mm/rev in NI metals / - mm/rev in superalloys / - mm/rev in hardened steels · Vc max.: - m/min in steel / - m/min in stainless / - m/min in cast / 505 m/min in NI metals / - m/min in superalloys / - m/min in hardened steels · Vc min.: - m/min in steel / - m/min in stainless / - m/min in cast / 135 m/min in NI metals / - m/min in superalloys / - m/min in hardened steels · Min. cutting depth: - mm in steel / - mm in stainless / - mm in cast / 0.3 mm in NI metals / - mm in superalloys / - mm in hardened steels · Max. cutting depth: - mm in steel / - mm in stainless / - mm in cast / 4 mm in NI metals / - mm in superalloys / - mm in hardened steels · Min. feed rate: - mm/rev in steel / - mm/rev in stainless steel / - mm/rev in cast / 0.06 mm/rev in NI metals / - mm/rev in superalloys / - mm/rev in hardened steels

For the processing of aluminium Further technical information: · d: 9.525mm · Area of application: Aluminium processing · r: 0.2mm · d1: 4.4mm · s: 4,76mm · l: 16,6mm · Max. feed rate: - mm/rev in steel / - mm/rev in stainless steel / - mm/rev in cast / 0.1 mm/rev in NI metals / - mm/rev in superalloys / - mm/rev in hardened steels · Vc max.: - m/min in steel / - m/min in stainless / - m/min in cast / 595 m/min in NI metals / - m/min in superalloys / - m/min in hardened steels · Vc min.: - m/min in steel / - m/min in stainless / - m/min in cast / 165 m/min in NI metals / - m/min in superalloys / - m/min in hardened steels · Min. cutting depth: - mm in steel / - mm in stainless / - mm in cast / 0.3 mm in NI metals / - mm in superalloys / - mm in hardened steels · Max. cutting depth: - mm in steel / - mm in stainless / - mm in cast / 4 mm in NI metals / - mm in superalloys / - mm in hardened steels · Min. feed rate: - mm/rev in steel / - mm/rev in stainless steel / - mm/rev in cast / 0.06 mm/rev in NI metals / - mm/rev in superalloys / - mm/rev in hardened steels

For the processing of aluminium Further technical information: · d: 6.35mm · Area of application: Aluminium processing · r: 0.2mm · d1: 2.8mm · s: 3,18mm · l: 11,1mm · Max. feed rate: - mm/rev in steel / - mm/rev in stainless steel / - mm/rev in cast / 0.1 mm/rev in NI metals / - mm/rev in superalloys / - mm/rev in hardened steels · Vc max.: - m/min in steel / - m/min in stainless / - m/min in cast / 505 m/min in NI metals / - m/min in superalloys / - m/min in hardened steels · Vc min.: - m/min in steel / - m/min in stainless / - m/min in cast / 140 m/min in NI metals / - m/min in superalloys / - m/min in hardened steels · Min. cutting depth: - mm in steel / - mm in stainless / - mm in cast / 0.3 mm in NI metals / - mm in superalloys / - mm in hardened steels · Max. cutting depth: - mm in steel / - mm in stainless / - mm in cast / 2.8 mm in NI metals / - mm in superalloys / - mm in hardened steels · Min. feed rate: - mm/rev in steel / - mm/rev in stainless steel / - mm/rev in cast / 0.06 mm/rev in NI metals / - mm/rev in superalloys / - mm/rev in hardened steels

For the processing of aluminium Further technical information: · d: 6.35mm · Area of application: Aluminium processing · r: 0.2mm · d1: 2.8mm · s: 3,18mm · l: 11,1mm · Max. feed rate: - mm/rev in steel / - mm/rev in stainless steel / - mm/rev in cast / 0.1 mm/rev in NI metals / - mm/rev in superalloys / - mm/rev in hardened steels · Vc max.: - m/min in steel / - m/min in stainless / - m/min in cast / 595 m/min in NI metals / - m/min in superalloys / - m/min in hardened steels · Vc min.: - m/min in steel / - m/min in stainless / - m/min in cast / 165 m/min in NI metals / - m/min in superalloys / - m/min in hardened steels · Min. cutting depth: - mm in steel / - mm in stainless / - mm in cast / 0.3 mm in NI metals / - mm in superalloys / - mm in hardened steels · Max. cutting depth: - mm in steel / - mm in stainless / - mm in cast / 2.8 mm in NI metals / - mm in superalloys / - mm in hardened steels · Min. feed rate: - mm/rev in steel / - mm/rev in stainless steel / - mm/rev in cast / 0.06 mm/rev in NI metals / - mm/rev in superalloys / - mm/rev in hardened steels