- Homepage
- Workplace equipment
- Chip removal
- Drill bits
- Twist drills
- Twist drills
- Twist drill PROMAT
Workplace equipment
Description:
point angle 118° · with straight shank · right-hand cutting · good self centring · pointed diagonal cutter · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,01mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,02mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,03mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,03mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,04mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,04mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,04mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,05mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,05mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,05mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,05mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,05mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,06mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,06mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,06mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,07mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,07mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,09mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,09mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,11mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,11mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,11mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,11mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,12mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,12mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,12mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,12mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,12mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,14mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,17mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 1000 N: 0,17mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,02mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,03mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,03mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,03mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,04mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,04mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,04mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,06mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,06mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,06mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,06mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,11mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,11mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,11mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,15mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,15mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,15mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,15mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,17mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,17mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,18mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,19mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,19mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,23mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,23mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,24mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,25mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,25mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,25mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,26mm/rev · Quality: Profile-ground · Overall length: Extra-short
Description:
HSS-Co · DIN 1897 · Type UNI · For universal use · Point angle 118° · With straight shank · Right-hand cutting · Good self-centring behaviour · Pointed cross-cut · For non-ferrous metals, structural and carbon steels, high-alloy steels (e.g. V2A/V4A), tool steels, castings and cast alloys, magnesium alloys, plastics, and aluminium · Advantages: Special ground section and special point thinning for low torque and quiet running · Round groove profile for optimum chip removal, even long chips from tough materials Industrial quality Further technical information: · Feed in steel up to 800 N: 0,27mm/rev · Quality: Profile-ground · Overall length: Extra-short
Coating
Cutting material
Length of spiral
Marker
Nominal Ø
Overall length
Point angle
Shank design
Standard
Type
Download
4000862431
Uncoated
HSS-Co
6 mm
PROMAT
1 mm
26 mm
118 °
Straight shank
DIN 1897
UNI
4000862433
Uncoated
HSS-Co
8 mm
PROMAT
1.2 mm
30 mm
118 °
Straight shank
DIN 1897
UNI
4000862436
Uncoated
HSS-Co
9 mm
PROMAT
1.5 mm
32 mm
118 °
Straight shank
DIN 1897
UNI
4000862438
Uncoated
HSS-Co
10 mm
PROMAT
1.7 mm
34 mm
118 °
Straight shank
DIN 1897
UNI
4000862440
Uncoated
HSS-Co
11 mm
PROMAT
1.9 mm
36 mm
118 °
Straight shank
DIN 1897
UNI
4000862441
Uncoated
HSS-Co
12 mm
PROMAT
2 mm
38 mm
118 °
Straight shank
DIN 1897
UNI
4000862442
Uncoated
HSS-Co
12 mm
PROMAT
2.1 mm
38 mm
118 °
Straight shank
DIN 1897
UNI
4000862444
Uncoated
HSS-Co
13 mm
PROMAT
2.3 mm
40 mm
118 °
Straight shank
DIN 1897
UNI
4000862445
Uncoated
HSS-Co
14 mm
PROMAT
2.4 mm
43 mm
118 °
Straight shank
DIN 1897
UNI
4000862446
Uncoated
HSS-Co
14 mm
PROMAT
2.5 mm
43 mm
118 °
Straight shank
DIN 1897
UNI
4000862447
Uncoated
HSS-Co
14 mm
PROMAT
2.6 mm
43 mm
118 °
Straight shank
DIN 1897
UNI
4000862448
Uncoated
HSS-Co
16 mm
PROMAT
2.7 mm
46 mm
118 °
Straight shank
DIN 1897
UNI
4000862449
Uncoated
HSS-Co
16 mm
PROMAT
2.8 mm
46 mm
118 °
Straight shank
DIN 1897
UNI
4000862451
Uncoated
HSS-Co
16 mm
PROMAT
3 mm
46 mm
118 °
Straight shank
DIN 1897
UNI
4000862452
Uncoated
HSS-Co
18 mm
PROMAT
3.1 mm
49 mm
118 °
Straight shank
DIN 1897
UNI
4000862454
Uncoated
HSS-Co
18 mm
PROMAT
3.3 mm
49 mm
118 °
Straight shank
DIN 1897
UNI
4000862458
Uncoated
HSS-Co
20 mm
PROMAT
3.7 mm
52 mm
118 °
Straight shank
DIN 1897
UNI
4000862466
Uncoated
HSS-Co
24 mm
PROMAT
4.5 mm
58 mm
118 °
Straight shank
DIN 1897
UNI
4000862467
Uncoated
HSS-Co
24 mm
PROMAT
4.6 mm
58 mm
118 °
Straight shank
DIN 1897
UNI
4000862471
Uncoated
HSS-Co
26 mm
PROMAT
5 mm
62 mm
118 °
Straight shank
DIN 1897
UNI
4000862476
Uncoated
HSS-Co
28 mm
PROMAT
5.5 mm
66 mm
118 °
Straight shank
DIN 1897
UNI
4000862477
Uncoated
HSS-Co
28 mm
PROMAT
5.6 mm
66 mm
118 °
Straight shank
DIN 1897
UNI
4000862481
Uncoated
HSS-Co
28 mm
PROMAT
6 mm
66 mm
118 °
Straight shank
DIN 1897
UNI
4000862484
Uncoated
HSS-Co
31 mm
PROMAT
6.3 mm
70 mm
118 °
Straight shank
DIN 1897
UNI
4000862489
Uncoated
HSS-Co
34 mm
PROMAT
6.8 mm
74 mm
118 °
Straight shank
DIN 1897
UNI
4000862490
Uncoated
HSS-Co
34 mm
PROMAT
6.9 mm
74 mm
118 °
Straight shank
DIN 1897
UNI
4000862493
Uncoated
HSS-Co
34 mm
PROMAT
7.2 mm
74 mm
118 °
Straight shank
DIN 1897
UNI
4000862494
Uncoated
HSS-Co
34 mm
PROMAT
7.3 mm
74 mm
118 °
Straight shank
DIN 1897
UNI
4000862495
Uncoated
HSS-Co
34 mm
PROMAT
7.4 mm
74 mm
118 °
Straight shank
DIN 1897
UNI
4000862496
Uncoated
HSS-Co
34 mm
PROMAT
7.5 mm
74 mm
118 °
Straight shank
DIN 1897
UNI
4000862497
Uncoated
HSS-Co
37 mm
PROMAT
7.6 mm
79 mm
118 °
Straight shank
DIN 1897
UNI
4000862498
Uncoated
HSS-Co
37 mm
PROMAT
7.7 mm
79 mm
118 °
Straight shank
DIN 1897
UNI
4000862499
Uncoated
HSS-Co
37 mm
PROMAT
7.8 mm
79 mm
118 °
Straight shank
DIN 1897
UNI
4000862503
Uncoated
HSS-Co
37 mm
PROMAT
8.2 mm
79 mm
118 °
Straight shank
DIN 1897
UNI
4000862504
Uncoated
HSS-Co
37 mm
PROMAT
8.3 mm
79 mm
118 °
Straight shank
DIN 1897
UNI
4000862505
Uncoated
HSS-Co
37 mm
PROMAT
8.4 mm
79 mm
118 °
Straight shank
DIN 1897
UNI
4000862506
Uncoated
HSS-Co
37 mm
PROMAT
8.5 mm
79 mm
118 °
Straight shank
DIN 1897
UNI
4000862508
Uncoated
HSS-Co
40 mm
PROMAT
9 mm
84 mm
118 °
Straight shank
DIN 1897
UNI
4000862511
Uncoated
HSS-Co
43 mm
PROMAT
9.8 mm
89 mm
118 °
Straight shank
DIN 1897
UNI
4000862512
Uncoated
HSS-Co
43 mm
PROMAT
10 mm
89 mm
118 °
Straight shank
DIN 1897
UNI
4000862514
Uncoated
HSS-Co
43 mm
PROMAT
10.5 mm
89 mm
118 °
Straight shank
DIN 1897
UNI
4000862515
Uncoated
HSS-Co
47 mm
PROMAT
11 mm
95 mm
118 °
Straight shank
DIN 1897
UNI
4000862516
Uncoated
HSS-Co
47 mm
PROMAT
11.5 mm
95 mm
118 °
Straight shank
DIN 1897
UNI
4000862517
Uncoated
HSS-Co
51 mm
PROMAT
12 mm
102 mm
118 °
Straight shank
DIN 1897
UNI
4000862518
Uncoated
HSS-Co
51 mm
PROMAT
12.5 mm
102 mm
118 °
Straight shank
DIN 1897
UNI
4000862519
Uncoated
HSS-Co
51 mm
PROMAT
13 mm
102 mm
118 °
Straight shank
DIN 1897
UNI
4000862520
Uncoated
HSS-Co
54 mm
PROMAT
13.5 mm
107 mm
118 °
Straight shank
DIN 1897
UNI
4000862525
TiN-coated
HSS-Co
6 mm
PROMAT
1 mm
26 mm
118 °
Straight shank
DIN 1897
UNI
4000862527
TiN-coated
HSS-Co
8 mm
PROMAT
1.2 mm
30 mm
118 °
Straight shank
DIN 1897
UNI
4000862528
TiN-coated
HSS-Co
8 mm
PROMAT
1.3 mm
30 mm
118 °
Straight shank
DIN 1897
UNI
4000862529
TiN-coated
HSS-Co
9 mm
PROMAT
1.4 mm
32 mm
118 °
Straight shank
DIN 1897
UNI
4000862531
TiN-coated
HSS-Co
10 mm
PROMAT
1.6 mm
34 mm
118 °
Straight shank
DIN 1897
UNI
4000862532
TiN-coated
HSS-Co
10 mm
PROMAT
1.7 mm
34 mm
118 °
Straight shank
DIN 1897
UNI
4000862533
TiN-coated
HSS-Co
11 mm
PROMAT
1.8 mm
36 mm
118 °
Straight shank
DIN 1897
UNI
4000862534
TiN-coated
HSS-Co
11 mm
PROMAT
1.9 mm
36 mm
118 °
Straight shank
DIN 1897
UNI
4000862535
TiN-coated
HSS-Co
12 mm
PROMAT
2 mm
38 mm
118 °
Straight shank
DIN 1897
UNI
4000862536
TiN-coated
HSS-Co
12 mm
PROMAT
2.1 mm
38 mm
118 °
Straight shank
DIN 1897
UNI
4000862537
TiN-coated
HSS-Co
13 mm
PROMAT
2.2 mm
40 mm
118 °
Straight shank
DIN 1897
UNI
4000862539
TiN-coated
HSS-Co
14 mm
PROMAT
2.4 mm
43 mm
118 °
Straight shank
DIN 1897
UNI
4000862541
TiN-coated
HSS-Co
14 mm
PROMAT
2.6 mm
43 mm
118 °
Straight shank
DIN 1897
UNI
4000862542
TiN-coated
HSS-Co
16 mm
PROMAT
2.7 mm
46 mm
118 °
Straight shank
DIN 1897
UNI
4000862544
TiN-coated
HSS-Co
16 mm
PROMAT
2.9 mm
46 mm
118 °
Straight shank
DIN 1897
UNI
4000862545
TiN-coated
HSS-Co
16 mm
PROMAT
3 mm
46 mm
118 °
Straight shank
DIN 1897
UNI
4000862548
TiN-coated
HSS-Co
18 mm
PROMAT
3.3 mm
49 mm
118 °
Straight shank
DIN 1897
UNI
4000862550
TiN-coated
HSS-Co
20 mm
PROMAT
3.5 mm
52 mm
118 °
Straight shank
DIN 1897
UNI
4000862551
TiN-coated
HSS-Co
20 mm
PROMAT
3.6 mm
52 mm
118 °
Straight shank
DIN 1897
UNI
4000862553
TiN-coated
HSS-Co
22 mm
PROMAT
3.8 mm
55 mm
118 °
Straight shank
DIN 1897
UNI
4000862555
TiN-coated
HSS-Co
22 mm
PROMAT
4 mm
55 mm
118 °
Straight shank
DIN 1897
UNI
4000862558
TiN-coated
HSS-Co
24 mm
PROMAT
4.3 mm
58 mm
118 °
Straight shank
DIN 1897
UNI
4000862560
TiN-coated
HSS-Co
24 mm
PROMAT
4.5 mm
58 mm
118 °
Straight shank
DIN 1897
UNI
4000862562
TiN-coated
HSS-Co
24 mm
PROMAT
4.7 mm
58 mm
118 °
Straight shank
DIN 1897
UNI
4000862564
TiN-coated
HSS-Co
26 mm
PROMAT
4.9 mm
62 mm
118 °
Straight shank
DIN 1897
UNI
4000862566
TiN-coated
HSS-Co
26 mm
PROMAT
5.1 mm
62 mm
118 °
Straight shank
DIN 1897
UNI
4000862567
TiN-coated
HSS-Co
26 mm
PROMAT
5.2 mm
62 mm
118 °
Straight shank
DIN 1897
UNI
4000862570
TiN-coated
HSS-Co
28 mm
PROMAT
5.5 mm
66 mm
118 °
Straight shank
DIN 1897
UNI
4000862572
TiN-coated
HSS-Co
28 mm
PROMAT
5.7 mm
66 mm
118 °
Straight shank
DIN 1897
UNI
4000862573
TiN-coated
HSS-Co
28 mm
PROMAT
5.8 mm
66 mm
118 °
Straight shank
DIN 1897
UNI
4000862574
TiN-coated
HSS-Co
28 mm
PROMAT
5.9 mm
66 mm
118 °
Straight shank
DIN 1897
UNI
4000862578
TiN-coated
HSS-Co
31 mm
PROMAT
6.3 mm
70 mm
118 °
Straight shank
DIN 1897
UNI
4000862579
TiN-coated
HSS-Co
31 mm
PROMAT
6.4 mm
70 mm
118 °
Straight shank
DIN 1897
UNI
4000862580
TiN-coated
HSS-Co
31 mm
PROMAT
6.5 mm
70 mm
118 °
Straight shank
DIN 1897
UNI
4000862581
TiN-coated
HSS-Co
31 mm
PROMAT
6.6 mm
70 mm
118 °
Straight shank
DIN 1897
UNI
4000862582
TiN-coated
HSS-Co
31 mm
PROMAT
6.7 mm
70 mm
118 °
Straight shank
DIN 1897
UNI
4000862583
TiN-coated
HSS-Co
34 mm
PROMAT
6.8 mm
74 mm
118 °
Straight shank
DIN 1897
UNI
4000862586
TiN-coated
HSS-Co
34 mm
PROMAT
7.1 mm
74 mm
118 °
Straight shank
DIN 1897
UNI
4000862589
TiN-coated
HSS-Co
34 mm
PROMAT
7.4 mm
74 mm
118 °
Straight shank
DIN 1897
UNI
4000862591
TiN-coated
HSS-Co
37 mm
PROMAT
7.6 mm
79 mm
118 °
Straight shank
DIN 1897
UNI
4000862596
TiN-coated
HSS-Co
37 mm
PROMAT
8.1 mm
79 mm
118 °
Straight shank
DIN 1897
UNI
4000862597
TiN-coated
HSS-Co
37 mm
PROMAT
8.2 mm
79 mm
118 °
Straight shank
DIN 1897
UNI
4000862598
TiN-coated
HSS-Co
37 mm
PROMAT
8.3 mm
79 mm
118 °
Straight shank
DIN 1897
UNI
4000862599
TiN-coated
HSS-Co
37 mm
PROMAT
8.4 mm
79 mm
118 °
Straight shank
DIN 1897
UNI
4000862600
TiN-coated
HSS-Co
37 mm
PROMAT
8.5 mm
79 mm
118 °
Straight shank
DIN 1897
UNI
4000862601
TiN-coated
HSS-Co
40 mm
PROMAT
8.8 mm
84 mm
118 °
Straight shank
DIN 1897
UNI
4000862602
TiN-coated
HSS-Co
40 mm
PROMAT
9 mm
84 mm
118 °
Straight shank
DIN 1897
UNI
4000862603
TiN-coated
HSS-Co
40 mm
PROMAT
9.3 mm
84 mm
118 °
Straight shank
DIN 1897
UNI
4000862605
TiN-coated
HSS-Co
43 mm
PROMAT
9.8 mm
89 mm
118 °
Straight shank
DIN 1897
UNI
4000862608
TiN-coated
HSS-Co
43 mm
PROMAT
10.5 mm
89 mm
118 °
Straight shank
DIN 1897
UNI
4000862611
TiN-coated
HSS-Co
51 mm
PROMAT
12 mm
102 mm
118 °
Straight shank
DIN 1897
UNI
4000862613
TiN-coated
HSS-Co
51 mm
PROMAT
13 mm
102 mm
118 °
Straight shank
DIN 1897
UNI
4000862615
TiN-coated
HSS-Co
54 mm
PROMAT
14 mm
107 mm
118 °
Straight shank
DIN 1897
UNI
Please select a product variant to specifically search for it in the shops of our dealers.