For a very light and soft cut for thin, long shafts and thin-walled material Further technical information: · d: 12.7mm · r: 0.4mm · d1: 5.16mm · s: 4,76mm · l: 12,9mm · Max. feed rate: 0.3 mm/rev in steel / 0.23 mm/rev in stainless steel / 0.3 mm/rev in cast / 0.3 mm/rev in NI metals / 0.23 mm/rev in superalloys / - mm/rev in hardened steels · Vc max.: 215 m/min in steel / 125 m/min in stainless / 200 m/min in cast / 750 m/min in NI metals / 60 m/min in superalloys / - m/min in hardened steels · Vc min.: 160 m/min in steel / 95 m/min in stainless / 150 m/min in cast / 240 m/min in NI metals / 30 m/min in superalloys / - m/min in hardened steels · Min. cutting depth: 0.8 mm in steel / 0.8 mm in stainless / 0.8 mm in cast / 0.8 mm in NI metals / 0.8 mm in superalloys / - mm in hardened steels · Max. cutting depth: 5 mm in steel / 3.8 mm in stainless / 5 mm in cast / 5 mm in NI metals / 3 mm in superalloys / - mm in hardened steels · Min. feed rate: 0.2 mm/rev in steel / 0.2 mm/rev in stainless steel / 0.2 mm/rev in cast / 0.2 mm/rev in NI metals / 0.2 mm/rev in superalloys / - mm/rev in hardened steels

For a very light and soft cut for thin, long shafts and thin-walled material Further technical information: · d: 12.7mm · r: 0.8mm · d1: 5.16mm · s: 4,76mm · l: 12,9mm · Max. feed rate: 0.5 mm/rev in steel / 0.38 mm/rev in stainless steel / 0.5 mm/rev in cast / 0.5 mm/rev in NI metals / 0.3 mm/rev in superalloys / - mm/rev in hardened steels · Vc max.: 255 m/min in steel / 150 m/min in stainless / 240 m/min in cast / 890 m/min in NI metals / 75 m/min in superalloys / - m/min in hardened steels · Vc min.: 165 m/min in steel / 95 m/min in stainless / 155 m/min in cast / 245 m/min in NI metals / 30 m/min in superalloys / - m/min in hardened steels · Min. cutting depth: 0.8 mm in steel / 0.8 mm in stainless / 0.8 mm in cast / 0.8 mm in NI metals / 0.8 mm in superalloys / - mm in hardened steels · Max. cutting depth: 5 mm in steel / 3.8 mm in stainless / 5 mm in cast / 5 mm in NI metals / 3 mm in superalloys / - mm in hardened steels · Min. feed rate: 0.2 mm/rev in steel / 0.2 mm/rev in stainless steel / 0.2 mm/rev in cast / 0.2 mm/rev in NI metals / 0.2 mm/rev in superalloys / - mm/rev in hardened steels

For a very light and soft cut for thin, long shafts and thin-walled material Further technical information: · d: 12.7mm · r: 0.4mm · d1: 5.16mm · s: 4,76mm · l: 12,9mm · Max. feed rate: 0.3 mm/rev in steel / 0.23 mm/rev in stainless steel / 0.3 mm/rev in cast / 0.3 mm/rev in NI metals / 0.23 mm/rev in superalloys / - mm/rev in hardened steels · Vc max.: 215 m/min in steel / 125 m/min in stainless / 200 m/min in cast / 750 m/min in NI metals / 60 m/min in superalloys / - m/min in hardened steels · Vc min.: 160 m/min in steel / 95 m/min in stainless / 150 m/min in cast / 240 m/min in NI metals / 30 m/min in superalloys / - m/min in hardened steels · Min. cutting depth: 0.8 mm in steel / 0.8 mm in stainless / 0.8 mm in cast / 0.8 mm in NI metals / 0.8 mm in superalloys / - mm in hardened steels · Max. cutting depth: 5 mm in steel / 3.8 mm in stainless / 5 mm in cast / 5 mm in NI metals / 3 mm in superalloys / - mm in hardened steels · Min. feed rate: 0.2 mm/rev in steel / 0.2 mm/rev in stainless steel / 0.2 mm/rev in cast / 0.2 mm/rev in NI metals / 0.2 mm/rev in superalloys / - mm/rev in hardened steels

For a very light and soft cut for thin, long shafts and thin-walled material Further technical information: · d: 12.7mm · r: 0.8mm · d1: 5.16mm · s: 4,76mm · l: 12,9mm · Max. feed rate: 0.5 mm/rev in steel / 0.38 mm/rev in stainless steel / 0.5 mm/rev in cast / 0.5 mm/rev in NI metals / 0.3 mm/rev in superalloys / - mm/rev in hardened steels · Vc max.: 255 m/min in steel / 150 m/min in stainless / 240 m/min in cast / 890 m/min in NI metals / 75 m/min in superalloys / - m/min in hardened steels · Vc min.: 165 m/min in steel / 95 m/min in stainless / 155 m/min in cast / 245 m/min in NI metals / 30 m/min in superalloys / - m/min in hardened steels · Min. cutting depth: 0.8 mm in steel / 0.8 mm in stainless / 0.8 mm in cast / 0.8 mm in NI metals / 0.8 mm in superalloys / - mm in hardened steels · Max. cutting depth: 5 mm in steel / 3.8 mm in stainless / 5 mm in cast / 5 mm in NI metals / 3 mm in superalloys / - mm in hardened steels · Min. feed rate: 0.2 mm/rev in steel / 0.2 mm/rev in stainless steel / 0.2 mm/rev in cast / 0.2 mm/rev in NI metals / 0.2 mm/rev in superalloys / - mm/rev in hardened steels