- Homepage
- Tools
- Chip removal
- Drill bits
- Twist drills
- Twist drills
- Deep-hole drill PROMAT
Tools
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,05mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,06mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,05mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,06mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,09mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,11mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,12mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,15mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,17mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,18mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,19mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,09mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,11mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,12mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,15mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,17mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,18mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,19mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,09mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,11mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,12mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,15mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,17mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,18mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,19mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,2mm/rev · Quality: Profile-ground · Overall length: Series 3
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,04mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,04mm/rev · Quality: Profile-ground · Overall length: Series 1
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,04mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,05mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,06mm/rev · Quality: Profile-ground · Overall length: Series 2
Description:
HSS · DIN 1869 · Type TS · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Extra-long type · Special drill for extremely deep bores · For drilling in all long-chipping materials e.g. steel up to approx. 1,000 N/mm², aluminium alloys, Al-Si alloys, electrolytic copper, tough brass, cast iron Further technical information: · Feed in steel up to 800 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Series 3
Coating
Cutting material
Length of spiral
Marker
Nominal Ø
Overall length
Point angle
Shank design
Standard
Type
Download
4000861101
Uncoated
HSS
105 mm
PROMAT
3.2 mm
155 mm
130 °
Straight shank
DIN 1869
TS
4000861103
Uncoated
HSS
135 mm
PROMAT
3.2 mm
200 mm
130 °
Straight shank
DIN 1869
TS
4000861104
Uncoated
HSS
150 mm
PROMAT
4.2 mm
220 mm
130 °
Straight shank
DIN 1869
TS
4000861106
Uncoated
HSS
200 mm
PROMAT
6.8 mm
290 mm
130 °
Straight shank
DIN 1869
TS
4000861107
Uncoated
HSS
235 mm
PROMAT
10.2 mm
340 mm
130 °
Straight shank
DIN 1869
TS
4000861108
Uncoated
HSS
135 mm
PROMAT
2 mm
200 mm
130 °
Straight shank
DIN 1869
TS
4000861109
Uncoated
HSS
150 mm
PROMAT
2.5 mm
225 mm
130 °
Straight shank
DIN 1869
TS
4000861111
Uncoated
HSS
170 mm
PROMAT
3.2 mm
250 mm
130 °
Straight shank
DIN 1869
TS
4000861112
Uncoated
HSS
190 mm
PROMAT
4.2 mm
280 mm
130 °
Straight shank
DIN 1869
TS
4000861113
Uncoated
HSS
250 mm
PROMAT
6.8 mm
370 mm
130 °
Straight shank
DIN 1869
TS
4000861114
Uncoated
HSS
295 mm
PROMAT
10.2 mm
430 mm
130 °
Straight shank
DIN 1869
TS
4000861131
Uncoated
HSS
85 mm
PROMAT
2 mm
125 mm
130 °
Straight shank
DIN 1869
TS
4000861132
Uncoated
HSS
95 mm
PROMAT
2.5 mm
140 mm
130 °
Straight shank
DIN 1869
TS
4000861133
Uncoated
HSS
100 mm
PROMAT
3 mm
150 mm
130 °
Straight shank
DIN 1869
TS
4000861134
Uncoated
HSS
105 mm
PROMAT
3.3 mm
155 mm
130 °
Straight shank
DIN 1869
TS
4000861135
Uncoated
HSS
115 mm
PROMAT
3.5 mm
165 mm
130 °
Straight shank
DIN 1869
TS
4000861136
Uncoated
HSS
120 mm
PROMAT
4 mm
175 mm
130 °
Straight shank
DIN 1869
TS
4000861137
Uncoated
HSS
120 mm
PROMAT
4.2 mm
175 mm
130 °
Straight shank
DIN 1869
TS
4000861138
Uncoated
HSS
125 mm
PROMAT
4.5 mm
185 mm
130 °
Straight shank
DIN 1869
TS
4000861139
Uncoated
HSS
135 mm
PROMAT
5 mm
195 mm
130 °
Straight shank
DIN 1869
TS
4000861140
Uncoated
HSS
140 mm
PROMAT
5.5 mm
205 mm
130 °
Straight shank
DIN 1869
TS
4000861141
Uncoated
HSS
140 mm
PROMAT
6 mm
205 mm
130 °
Straight shank
DIN 1869
TS
4000861142
Uncoated
HSS
150 mm
PROMAT
6.5 mm
215 mm
130 °
Straight shank
DIN 1869
TS
4000861143
Uncoated
HSS
155 mm
PROMAT
6.8 mm
225 mm
130 °
Straight shank
DIN 1869
TS
4000861144
Uncoated
HSS
155 mm
PROMAT
7 mm
225 mm
130 °
Straight shank
DIN 1869
TS
4000861145
Uncoated
HSS
155 mm
PROMAT
7.5 mm
225 mm
130 °
Straight shank
DIN 1869
TS
4000861146
Uncoated
HSS
165 mm
PROMAT
8 mm
240 mm
130 °
Straight shank
DIN 1869
TS
4000861147
Uncoated
HSS
165 mm
PROMAT
8.5 mm
240 mm
130 °
Straight shank
DIN 1869
TS
4000861148
Uncoated
HSS
175 mm
PROMAT
9 mm
250 mm
130 °
Straight shank
DIN 1869
TS
4000861149
Uncoated
HSS
175 mm
PROMAT
9.5 mm
250 mm
130 °
Straight shank
DIN 1869
TS
4000861150
Uncoated
HSS
185 mm
PROMAT
10 mm
265 mm
130 °
Straight shank
DIN 1869
TS
4000861151
Uncoated
HSS
185 mm
PROMAT
10.2 mm
265 mm
130 °
Straight shank
DIN 1869
TS
4000861152
Uncoated
HSS
185 mm
PROMAT
10.5 mm
265 mm
130 °
Straight shank
DIN 1869
TS
4000861153
Uncoated
HSS
195 mm
PROMAT
11 mm
280 mm
130 °
Straight shank
DIN 1869
TS
4000861154
Uncoated
HSS
195 mm
PROMAT
11.5 mm
280 mm
130 °
Straight shank
DIN 1869
TS
4000861155
Uncoated
HSS
205 mm
PROMAT
12 mm
295 mm
130 °
Straight shank
DIN 1869
TS
4000861156
Uncoated
HSS
130 mm
PROMAT
3 mm
190 mm
130 °
Straight shank
DIN 1869
TS
4000861157
Uncoated
HSS
145 mm
PROMAT
3.5 mm
210 mm
130 °
Straight shank
DIN 1869
TS
4000861158
Uncoated
HSS
150 mm
PROMAT
4 mm
220 mm
130 °
Straight shank
DIN 1869
TS
4000861159
Uncoated
HSS
160 mm
PROMAT
4.5 mm
235 mm
130 °
Straight shank
DIN 1869
TS
4000861160
Uncoated
HSS
170 mm
PROMAT
5 mm
245 mm
130 °
Straight shank
DIN 1869
TS
4000861161
Uncoated
HSS
180 mm
PROMAT
5.5 mm
260 mm
130 °
Straight shank
DIN 1869
TS
4000861162
Uncoated
HSS
180 mm
PROMAT
6 mm
260 mm
130 °
Straight shank
DIN 1869
TS
4000861163
Uncoated
HSS
190 mm
PROMAT
6.5 mm
275 mm
130 °
Straight shank
DIN 1869
TS
4000861164
Uncoated
HSS
200 mm
PROMAT
7 mm
290 mm
130 °
Straight shank
DIN 1869
TS
4000861165
Uncoated
HSS
200 mm
PROMAT
7.5 mm
290 mm
130 °
Straight shank
DIN 1869
TS
4000861166
Uncoated
HSS
210 mm
PROMAT
8 mm
305 mm
130 °
Straight shank
DIN 1869
TS
4000861167
Uncoated
HSS
210 mm
PROMAT
8.5 mm
305 mm
130 °
Straight shank
DIN 1869
TS
4000861168
Uncoated
HSS
220 mm
PROMAT
9 mm
320 mm
130 °
Straight shank
DIN 1869
TS
4000861169
Uncoated
HSS
220 mm
PROMAT
9.5 mm
320 mm
130 °
Straight shank
DIN 1869
TS
4000861170
Uncoated
HSS
235 mm
PROMAT
10 mm
340 mm
130 °
Straight shank
DIN 1869
TS
4000861171
Uncoated
HSS
235 mm
PROMAT
10.5 mm
340 mm
130 °
Straight shank
DIN 1869
TS
4000861172
Uncoated
HSS
250 mm
PROMAT
11 mm
365 mm
130 °
Straight shank
DIN 1869
TS
4000861173
Uncoated
HSS
250 mm
PROMAT
11.5 mm
365 mm
130 °
Straight shank
DIN 1869
TS
4000861174
Uncoated
HSS
260 mm
PROMAT
12 mm
375 mm
130 °
Straight shank
DIN 1869
TS
4000861175
Uncoated
HSS
180 mm
PROMAT
3.5 mm
265 mm
130 °
Straight shank
DIN 1869
TS
4000861176
Uncoated
HSS
190 mm
PROMAT
4 mm
280 mm
130 °
Straight shank
DIN 1869
TS
4000861177
Uncoated
HSS
200 mm
PROMAT
4.5 mm
295 mm
130 °
Straight shank
DIN 1869
TS
4000861178
Uncoated
HSS
210 mm
PROMAT
5 mm
315 mm
130 °
Straight shank
DIN 1869
TS
4000861179
Uncoated
HSS
225 mm
PROMAT
5.5 mm
330 mm
130 °
Straight shank
DIN 1869
TS
4000861180
Uncoated
HSS
225 mm
PROMAT
6 mm
330 mm
130 °
Straight shank
DIN 1869
TS
4000861181
Uncoated
HSS
235 mm
PROMAT
6.5 mm
350 mm
130 °
Straight shank
DIN 1869
TS
4000861182
Uncoated
HSS
250 mm
PROMAT
7 mm
370 mm
130 °
Straight shank
DIN 1869
TS
4000861183
Uncoated
HSS
250 mm
PROMAT
7.5 mm
370 mm
130 °
Straight shank
DIN 1869
TS
4000861184
Uncoated
HSS
265 mm
PROMAT
8 mm
390 mm
130 °
Straight shank
DIN 1869
TS
4000861185
Uncoated
HSS
265 mm
PROMAT
8.5 mm
390 mm
130 °
Straight shank
DIN 1869
TS
4000861186
Uncoated
HSS
280 mm
PROMAT
9 mm
410 mm
130 °
Straight shank
DIN 1869
TS
4000861187
Uncoated
HSS
280 mm
PROMAT
9.5 mm
410 mm
130 °
Straight shank
DIN 1869
TS
4000861188
Uncoated
HSS
295 mm
PROMAT
10 mm
430 mm
130 °
Straight shank
DIN 1869
TS
4000861189
Uncoated
HSS
295 mm
PROMAT
10.5 mm
430 mm
130 °
Straight shank
DIN 1869
TS
4000861190
Uncoated
HSS
310 mm
PROMAT
11 mm
455 mm
130 °
Straight shank
DIN 1869
TS
4000861191
Uncoated
HSS
310 mm
PROMAT
11.5 mm
455 mm
130 °
Straight shank
DIN 1869
TS
4000861192
Uncoated
HSS
330 mm
PROMAT
12 mm
480 mm
130 °
Straight shank
DIN 1869
TS
4000861193
Uncoated
HSS
60 mm
PROMAT
1 mm
100 mm
130 °
Straight shank
DIN 1869
TS
4000861194
Uncoated
HSS
60 mm
PROMAT
1.5 mm
100 mm
130 °
Straight shank
DIN 1869
TS
4000861195
Uncoated
HSS
100 mm
PROMAT
1.5 mm
150 mm
130 °
Straight shank
DIN 1869
TS
4000861196
Uncoated
HSS
110 mm
PROMAT
2 mm
160 mm
130 °
Straight shank
DIN 1869
TS
4000861197
Uncoated
HSS
120 mm
PROMAT
2.5 mm
180 mm
130 °
Straight shank
DIN 1869
TS
4000861198
Uncoated
HSS
160 mm
PROMAT
3 mm
240 mm
130 °
Straight shank
DIN 1869
TS
Please select a product variant to specifically search for it in the shops of our dealers.