- Homepage
- Tools
- Chip removal
- Drill bits
- Twist drills
- Twist drills
- Twist drill PROMAT
Tools
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 30mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 30mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 30mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 30mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 30mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 30mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 30mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 30mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 30mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 30mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 30mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 30mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 35mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 35mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 35mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 35mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 35mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 35mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 35mm
Description:
HSS · DIN 338 · Type N · Point angle 118° · Right-hand cutting · Crosswise grinding according to DIN 1412 C · With offset shank · The fully ground twist drill has a higher concentricity · Uses: For steel, alloyed and unalloyed cast steel (up to 900 N/mm² strength), grey cast, malleable iron, ductile iron and die-cast, sintered iron, nickel silver, graphite, short-chipping aluminium alloys, brass and bronze · Ideal for drilling larger bore diameters for all conventional drills with a chuck up to 13.0 mm Further technical information: · Feed in steel up to 800 N: 0,14mm/rev · Quality: Profile-ground · Length of shank: 35mm
Coating
Cutting material
Length of spiral
Marker
Nominal Ø
Overall length
Point angle
Shank design
Shank Ø
Standard
Type
Download
4000860153
Uncoated
HSS
87 mm
PROMAT
10.5 mm
133 mm
118 °
Offset shank
10 mm
DIN 338
N
4000860154
Uncoated
HSS
94 mm
PROMAT
11 mm
142 mm
118 °
Offset shank
10 mm
DIN 338
N
4000860155
Uncoated
HSS
94 mm
PROMAT
11.5 mm
142 mm
118 °
Offset shank
10 mm
DIN 338
N
4000860156
Uncoated
HSS
101 mm
PROMAT
12 mm
151 mm
118 °
Offset shank
10 mm
DIN 338
N
4000860157
Uncoated
HSS
101 mm
PROMAT
12.5 mm
151 mm
118 °
Offset shank
10 mm
DIN 338
N
4000860158
Uncoated
HSS
101 mm
PROMAT
13 mm
151 mm
118 °
Offset shank
10 mm
DIN 338
N
4000860159
Uncoated
HSS
108 mm
PROMAT
13.5 mm
160 mm
118 °
Offset shank
10 mm
DIN 338
N
4000860160
Uncoated
HSS
108 mm
PROMAT
14 mm
160 mm
118 °
Offset shank
10 mm
DIN 338
N
4000860161
Uncoated
HSS
114 mm
PROMAT
14.5 mm
169 mm
118 °
Offset shank
10 mm
DIN 338
N
4000860162
Uncoated
HSS
114 mm
PROMAT
15 mm
169 mm
118 °
Offset shank
10 mm
DIN 338
N
4000860163
Uncoated
HSS
120 mm
PROMAT
15.5 mm
178 mm
118 °
Offset shank
10 mm
DIN 338
N
4000860164
Uncoated
HSS
120 mm
PROMAT
16 mm
178 mm
118 °
Offset shank
10 mm
DIN 338
N
4000860165
Uncoated
HSS
125 mm
PROMAT
16.5 mm
184 mm
118 °
Offset shank
13 mm
DIN 338
N
4000860166
Uncoated
HSS
125 mm
PROMAT
17 mm
184 mm
118 °
Offset shank
13 mm
DIN 338
N
4000860167
Uncoated
HSS
130 mm
PROMAT
17.5 mm
191 mm
118 °
Offset shank
13 mm
DIN 338
N
4000860168
Uncoated
HSS
130 mm
PROMAT
18 mm
191 mm
118 °
Offset shank
13 mm
DIN 338
N
4000860169
Uncoated
HSS
135 mm
PROMAT
18.5 mm
198 mm
118 °
Offset shank
13 mm
DIN 338
N
4000860170
Uncoated
HSS
135 mm
PROMAT
19 mm
198 mm
118 °
Offset shank
13 mm
DIN 338
N
4000860171
Uncoated
HSS
140 mm
PROMAT
19.5 mm
205 mm
118 °
Offset shank
13 mm
DIN 338
N
4000860172
Uncoated
HSS
140 mm
PROMAT
20 mm
205 mm
118 °
Offset shank
13 mm
DIN 338
N
Please select a product variant to specifically search for it in the shops of our dealers.