- Homepage
- Tools
- Chip removal
- Drill bits
- Twist drills
- Twist drills
- Twist drill PROMAT
Tools
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,01mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,02mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,02mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,03mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,03mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,04mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,04mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,04mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,04mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,05mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,05mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,05mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,05mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,06mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,06mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,06mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,06mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,07mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,07mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,07mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,08mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,09mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,09mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,09mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,09mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,09mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,1mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,11mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,11mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,11mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,11mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,11mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,12mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,12mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,12mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,12mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,13mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,14mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,14mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,14mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,14mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,14mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,15mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,15mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,15mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,15mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,15mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,16mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,17mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,18mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,18mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,19mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co5 · DIN 338 · Type stainless steel · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · For drilling stainless steels, alloyed and unalloyed steels and types of cast iron with strengths above 800 N/mm² as well as tempering and case-hardening steels Further technical information: · Feed in steel up to 1000 N: 0,19mm/rev · Quality: Profile-ground · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,04mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,05mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,06mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,06mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,07mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,08mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,08mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,08mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,08mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,1mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,11mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,11mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,13mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,13mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,14mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,1mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,16mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,16mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,16mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,16mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,16mm/rev · Overall length: Short
Description:
HSS-Co8 · DIN 338 · Type N · Point angle 130° · Profile ground with crosswise grinding from Ø 2.0 mm · With straight shank · Right-hand cutting · Very powerful, robust twist drill with exceptional thermosetting resistance · Preferably to be used for processing strong and high-strength Cr/Ni-based alloys such as Hastelloy, Inconel, Monel, Nimonic, rust-, acid-, and heat-resistant steel and wear-resistant sheet materials · Steels and bronzes up to approx. 1,400 N/mm² in strength Further technical information: · Quality: Profile-ground · Feed in VA up to 800 N: 0,17mm/rev · Overall length: Short
Coating
Cutting material
Length of spiral
Marker
Nominal Ø
Overall length
Point angle
Shank design
Standard
Type
Download
4000860610
Uncoated
HSS-Co5
12 mm
PROMAT
1 mm
34 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860611
Uncoated
HSS-Co5
14 mm
PROMAT
1.1 mm
36 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860612
Uncoated
HSS-Co5
16 mm
PROMAT
1.2 mm
38 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860615
Uncoated
HSS-Co5
18 mm
PROMAT
1.5 mm
40 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860616
Uncoated
HSS-Co5
20 mm
PROMAT
1.6 mm
43 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860619
Uncoated
HSS-Co5
22 mm
PROMAT
1.9 mm
46 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860620
Uncoated
HSS-Co5
24 mm
PROMAT
2 mm
49 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860621
Uncoated
HSS-Co5
24 mm
PROMAT
2.1 mm
49 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860622
Uncoated
HSS-Co5
27 mm
PROMAT
2.2 mm
53 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860623
Uncoated
HSS-Co5
27 mm
PROMAT
2.3 mm
53 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860624
Uncoated
HSS-Co5
30 mm
PROMAT
2.4 mm
57 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860626
Uncoated
HSS-Co5
30 mm
PROMAT
2.6 mm
57 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860627
Uncoated
HSS-Co5
33 mm
PROMAT
2.7 mm
61 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860628
Uncoated
HSS-Co5
33 mm
PROMAT
2.8 mm
61 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860629
Uncoated
HSS-Co5
33 mm
PROMAT
2.9 mm
61 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860630
Uncoated
HSS-Co5
33 mm
PROMAT
3 mm
61 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860632
Uncoated
HSS-Co5
36 mm
PROMAT
3.2 mm
65 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860634
Uncoated
HSS-Co5
39 mm
PROMAT
3.4 mm
70 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860635
Uncoated
HSS-Co5
39 mm
PROMAT
3.5 mm
70 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860637
Uncoated
HSS-Co5
39 mm
PROMAT
3.7 mm
70 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860638
Uncoated
HSS-Co5
43 mm
PROMAT
3.8 mm
75 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860640
Uncoated
HSS-Co5
43 mm
PROMAT
4 mm
75 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860641
Uncoated
HSS-Co5
43 mm
PROMAT
4.1 mm
75 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860642
Uncoated
HSS-Co5
43 mm
PROMAT
4.2 mm
75 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860643
Uncoated
HSS-Co5
47 mm
PROMAT
4.3 mm
80 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860644
Uncoated
HSS-Co5
47 mm
PROMAT
4.4 mm
80 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860646
Uncoated
HSS-Co5
47 mm
PROMAT
4.6 mm
80 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860647
Uncoated
HSS-Co5
47 mm
PROMAT
4.7 mm
80 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860648
Uncoated
HSS-Co5
52 mm
PROMAT
4.8 mm
86 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860650
Uncoated
HSS-Co5
52 mm
PROMAT
5 mm
86 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860651
Uncoated
HSS-Co5
52 mm
PROMAT
5.1 mm
86 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860653
Uncoated
HSS-Co5
52 mm
PROMAT
5.3 mm
86 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860654
Uncoated
HSS-Co5
57 mm
PROMAT
5.4 mm
93 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860655
Uncoated
HSS-Co5
57 mm
PROMAT
5.5 mm
93 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860656
Uncoated
HSS-Co5
57 mm
PROMAT
5.6 mm
93 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860657
Uncoated
HSS-Co5
57 mm
PROMAT
5.7 mm
93 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860658
Uncoated
HSS-Co5
57 mm
PROMAT
5.8 mm
93 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860661
Uncoated
HSS-Co5
63 mm
PROMAT
6.1 mm
101 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860662
Uncoated
HSS-Co5
63 mm
PROMAT
6.2 mm
101 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860663
Uncoated
HSS-Co5
63 mm
PROMAT
6.3 mm
101 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860664
Uncoated
HSS-Co5
63 mm
PROMAT
6.4 mm
101 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860667
Uncoated
HSS-Co5
63 mm
PROMAT
6.7 mm
101 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860668
Uncoated
HSS-Co5
69 mm
PROMAT
6.8 mm
109 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860671
Uncoated
HSS-Co5
69 mm
PROMAT
7.1 mm
109 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860672
Uncoated
HSS-Co5
69 mm
PROMAT
7.2 mm
109 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860673
Uncoated
HSS-Co5
69 mm
PROMAT
7.3 mm
109 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860674
Uncoated
HSS-Co5
69 mm
PROMAT
7.4 mm
109 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860676
Uncoated
HSS-Co5
75 mm
PROMAT
7.6 mm
117 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860677
Uncoated
HSS-Co5
75 mm
PROMAT
7.7 mm
117 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860678
Uncoated
HSS-Co5
75 mm
PROMAT
7.8 mm
117 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860681
Uncoated
HSS-Co5
75 mm
PROMAT
8.1 mm
117 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860683
Uncoated
HSS-Co5
75 mm
PROMAT
8.3 mm
117 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860684
Uncoated
HSS-Co5
75 mm
PROMAT
8.4 mm
117 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860685
Uncoated
HSS-Co5
75 mm
PROMAT
8.5 mm
117 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860686
Uncoated
HSS-Co5
81 mm
PROMAT
8.6 mm
125 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860687
Uncoated
HSS-Co5
81 mm
PROMAT
8.7 mm
125 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860689
Uncoated
HSS-Co5
81 mm
PROMAT
8.9 mm
125 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860690
Uncoated
HSS-Co5
81 mm
PROMAT
9 mm
125 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860691
Uncoated
HSS-Co5
81 mm
PROMAT
9.1 mm
125 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860692
Uncoated
HSS-Co5
81 mm
PROMAT
9.2 mm
125 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860693
Uncoated
HSS-Co5
81 mm
PROMAT
9.3 mm
125 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860695
Uncoated
HSS-Co5
81 mm
PROMAT
9.5 mm
125 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860696
Uncoated
HSS-Co5
87 mm
PROMAT
9.6 mm
133 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860697
Uncoated
HSS-Co5
87 mm
PROMAT
9.7 mm
133 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860698
Uncoated
HSS-Co5
87 mm
PROMAT
9.8 mm
133 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860699
Uncoated
HSS-Co5
87 mm
PROMAT
9.9 mm
133 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860700
Uncoated
HSS-Co5
87 mm
PROMAT
10 mm
133 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860702
Uncoated
HSS-Co5
87 mm
PROMAT
10.2 mm
133 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860710
Uncoated
HSS-Co5
94 mm
PROMAT
11 mm
142 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860715
Uncoated
HSS-Co5
94 mm
PROMAT
11.5 mm
142 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860718
Uncoated
HSS-Co5
94 mm
PROMAT
11.8 mm
142 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860720
Uncoated
HSS-Co5
101 mm
PROMAT
12 mm
151 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860725
Uncoated
HSS-Co5
101 mm
PROMAT
12.5 mm
151 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860735
Uncoated
HSS-Co5
108 mm
PROMAT
13.5 mm
160 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860740
Uncoated
HSS-Co5
108 mm
PROMAT
14 mm
160 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860745
Uncoated
HSS-Co5
114 mm
PROMAT
14.5 mm
169 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860750
Uncoated
HSS-Co5
114 mm
PROMAT
15 mm
169 mm
130 °
Straight shank
DIN 338
Stainless steel
4000860755
Uncoated
HSS-Co5
120 mm
PROMAT
15.5 mm
178 mm
130 °
Straight shank
DIN 338
Stainless steel
4000862950
Uncoated
HSS-Co8
24 mm
PROMAT
2 mm
49 mm
130 °
Straight shank
DIN 338
N
4000862951
Uncoated
HSS-Co8
30 mm
PROMAT
2.5 mm
57 mm
130 °
Straight shank
DIN 338
N
4000862952
Uncoated
HSS-Co8
33 mm
PROMAT
3 mm
61 mm
130 °
Straight shank
DIN 338
N
4000862953
Uncoated
HSS-Co8
36 mm
PROMAT
3.2 mm
65 mm
130 °
Straight shank
DIN 338
N
4000862954
Uncoated
HSS-Co8
36 mm
PROMAT
3.3 mm
65 mm
130 °
Straight shank
DIN 338
N
4000862956
Uncoated
HSS-Co8
43 mm
PROMAT
4 mm
75 mm
130 °
Straight shank
DIN 338
N
4000862957
Uncoated
HSS-Co8
43 mm
PROMAT
4.1 mm
75 mm
130 °
Straight shank
DIN 338
N
4000862958
Uncoated
HSS-Co8
43 mm
PROMAT
4.2 mm
75 mm
130 °
Straight shank
DIN 338
N
4000862960
Uncoated
HSS-Co8
52 mm
PROMAT
4.8 mm
86 mm
130 °
Straight shank
DIN 338
N
4000862964
Uncoated
HSS-Co8
63 mm
PROMAT
6.5 mm
101 mm
130 °
Straight shank
DIN 338
N
4000862965
Uncoated
HSS-Co8
69 mm
PROMAT
6.8 mm
109 mm
130 °
Straight shank
DIN 338
N
4000862966
Uncoated
HSS-Co8
69 mm
PROMAT
7 mm
109 mm
130 °
Straight shank
DIN 338
N
4000862968
Uncoated
HSS-Co8
75 mm
PROMAT
8 mm
117 mm
130 °
Straight shank
DIN 338
N
4000862969
Uncoated
HSS-Co8
75 mm
PROMAT
8.5 mm
117 mm
130 °
Straight shank
DIN 338
N
4000862970
Uncoated
HSS-Co8
81 mm
PROMAT
9 mm
125 mm
130 °
Straight shank
DIN 338
N
4000862972
Uncoated
HSS-Co8
52 mm
PROMAT
5.1 mm
86 mm
130 °
Straight shank
DIN 338
N
4000862973
Uncoated
HSS-Co8
87 mm
PROMAT
10 mm
133 mm
130 °
Straight shank
DIN 338
N
4000862974
Uncoated
HSS-Co8
87 mm
PROMAT
10.2 mm
133 mm
130 °
Straight shank
DIN 338
N
4000862975
Uncoated
HSS-Co8
87 mm
PROMAT
10.5 mm
133 mm
130 °
Straight shank
DIN 338
N
4000862976
Uncoated
HSS-Co8
94 mm
PROMAT
11 mm
142 mm
130 °
Straight shank
DIN 338
N
4000862977
Uncoated
HSS-Co8
101 mm
PROMAT
12 mm
151 mm
130 °
Straight shank
DIN 338
N
4000862978
Uncoated
HSS-Co8
101 mm
PROMAT
13 mm
151 mm
130 °
Straight shank
DIN 338
N
Please select a product variant to specifically search for it in the shops of our dealers.